濟南專業防水http://www.unichase.com.cn/介紹填縫劑在冬季不能用于室外的，因?yàn)樘羁p劑的施工溫度在5-35℃之間。因?yàn)闇囟冗^低會導致填縫劑的性能下降，在室內使用則可以，因?yàn)楸狈降墓┡到y(tǒng)比較好，雖說室外的溫度在零下二三十?dāng)z氏度，但室內的溫度最低也保證在零上10℃，所以填縫劑在冬季可應用于室內。因此濟南專業防水建議大家在晚秋、冬季、初春的季節在北方不宜在室外進行填縫劑施工。
Jinan professional waterproof sealant presentation can not be used outdoors in the winter, because the construction temperature sealant between 5-35 ℃. Because the temperature is too low will result in sealant performance degradation

can be used indoors because of the North heating system is better, though the outdoor temperature at minus twenty or thirty degrees Celsius, but also guarantees a minimum indoor temperature at zero 10 ℃ so sealant can be used indoors

in the winter. Therefore, we recommend professional waterproof Jinan in late autumn, winter, early spring season in the North should not be performed in the outdoor construction sealant.

濟南專業防水分析在南方夏季的氣溫有的高達40℃，溫度過高也會使填縫劑的性能下降，所以在施工的時候大家一定要注意季節溫度的變化，使填縫劑的作用達到最佳的狀態。
Jinan professional waterproofing analysis in some southern summer temperatures as high as 40 ℃, the temperature was too high to make the sealant performance degradation, so when we must pay attention to the construction of seasonal

temperature changes, so that the role of sealant to achieve the most good condition.

濟南專業防水http://www.unichase.com.cn/建議大家使用時清除底材表面污物、油脂，并用少許水霧噴濕待填充部位，在0℃～40℃溫度范圍內施工使用，若在寒冷季節施工，為保證使用效果，建議將罐體放在30℃環境中預熱，施工前上下用力搖動一分鐘以上，施工時請將罐體始終保持倒置狀態。每罐施工完畢，請用專用清洗劑清洗膠槍螺紋部分，每次連續施工完畢，請用專用清洗劑清洗整個膠槍管，以免固化堵塞。修補和切割請?jiān)谂菽耆袒尚秃筮M(jìn)行，值得注意的是，切去泡沫的表皮會降低泡沫強度并降低泡沫的密封防水效果。
Jinan professional waterproof suggest that you remove the use of the substrate surface dirt, grease, and with a little mist wet the parts to be filled in the temperature range of 0 ℃ ~ 40 ℃ construction use, if the construction in the

cold season, to ensure the results, it is recommended the tank on the 30 ℃ environment preheated before construction shake down more than one minute, the construction of the tank please remain inverted state. Each tank construction is completed, wash with a special cleaning agent glue gun threaded portion, each successive construction is completed, clean the entire plastic barrel with a special cleaning agent, in order to avoid clogging cured. Repair and cutting in the fully cured foam after molding carried out, it is worth noting that cut skin foam reduces the strength of the foam and reducing the sealing waterproof foam.